xyzio

Posts Tagged ‘slicehost

Use Apache’s mod_proxy to Set Up a Proxy Server

leave a comment »

A proxy server is a server that sits between your computer and the internet and services your requests to the internet. Many companies use proxy servers to filter employee internet requests since a proxy server can also modify or block your request.

My goal in setting up a proxy server was to give myself a means of encrypting my web traffic when I am in insecure locations such as airports and restaurants.

Setup
To set up a proxy server, you first need a server. You can use a machine on your home network, get a dedicated server, or get a virtual server. I chose to get a virtual server through slicehost.com. I am using their base $20 256 slice with Ubuntu 8.04 LTS. In addition to proxy services I also use it as a virtual desktop and, since I can leave it on all the time, run long term jobs.

I set up the proxy server to only allow connections from the local host. I can then connect to the local machine via SSH and surf the web through the SSH tunnel. This way, the connection to my server is encrypted and no one can use the proxy server unless they have an account on my machine.

The setup is simple but I had to go to several sources to figure it all out, hence this article.

First, install Apache:

apt-get install apache2 apache2.2-common apache2-mpm-prefork apache2-utils libexpat1 ssl-cert

Next, link to the mod_proxy modules:

cd /etc/apache2/mods-enabled
ln -s /etc/apache2/mods-available/proxy_http.load
ln -s /etc/apache2/mods-available/proxy_ftp.load
ln -s /etc/apache2/mods-available/proxy_connect.load
ln -s /etc/apache2/mods-available/proxy.load

Then, in your httpd.conf file located at /etc/apache2 make
entries to configure the server:


ProxyRequests On
ProxyVia Block
<Proxy *>

   Order deny,allow
   Deny from all
   Allow from 127.0.0.1
</Proxy>

Here, ProxyRequests configures Apache as a forward proxy. <Proxy *> and </Proxy> delineate the proxy configuration block. The block tells Apache to deny all connections except from the local machine (127.0.0.1).

Now, restart Apache:

apache2ctl graceful

Finally, in your browser configure your host to use the proxy server you just set
up:

Sources:
slicehost.com: Ubuntu Hardy Apache and PHP install guide
serverwatch.com: Configuring Apache 2.0 as a Forward Proxy Server

Advertisements

Written by M Kapoor

November 1, 2009 at 11:40 pm

Using Amazon S3 via s3sync

leave a comment »

I have a VPS at Slicehost that I use to play around with Linux, it is much easier and convenient to use their remote service than dealing with the security, noise, and heat of running my own machine at home.  However their VPS doesn’t come with much disk space, the base 256MB plan only allows for 10GB of disk space.  So, I needed a way to offload my files so that I can shutdown my server when I don’t need it.  Slicehost pro-rates their charges so I don’t keep my VPS active unless I’m using it which saves me money.  I did a lot of research before settling on s3sync to save my files.  I tried using Jets3t but it requires Java which was slow and it is GUI based which means I had to run VNC to access it.  s3sync runs on Ruby and is on the command line which makes it perfect for running over SSH.

s3sync consists of two utilities, s3sync and s3cmd.  s3sync is a utility that will keep folders synchronized between Amazon S3 and your hard drive.  This utility is perfect for syncing your personal directories with Amazon for backups or to keep your development and production sites in sync.  s3cmd is billed as a counterpart to s3sync for managing your Amazon S3 account, however it is also great as a standalone tools for uploading, downloading, deleting, and managing single files.  I mostly use s3cmd on my VPS and that is what I’ll focus on here.

Assuming you are staring from a fresh installation, first install Ruby.  From Slicehost’s Ubuntu Ruby-on-Rails guide:

apt-get install ruby1.8-dev ruby1.8 ri1.8 rdoc1.8 irb1.8 libreadline-ruby1.8 libruby1.8 libopenssl-ruby

Then, install the symlinks:

sudo ln -s /usr/bin/ruby1.8 /usr/bin/ruby
sudo ln -s /usr/bin/ri1.8 /usr/bin/ri
sudo ln -s /usr/bin/rdoc1.8 /usr/bin/rdoc
sudo ln -s /usr/bin/irb1.8 /usr/bin/irb

Now, download, unzip, and untar s3sync:

wget http://s3.amazonaws.com/ServEdge_pub/s3sync/s3sync.tar.gz
gunzip s3sync.tar.gz
tar -xvvf s3sync.tar

You should now have a directory called s3sync containing the s3sync files.  Create a directory called .s3conf and copy the s3confg.yml.example file to it as s3config.yml.  This is where s3sync will look for its configuration options.  The README file lists additional locations you can specify the configuration options.

mkdir .s3conf
cp ./s3sync/s3config.yml.example ./.s3conf/s3config.yml

Finally, open .s3conf/s3config.yml and edit the aws_access_key_id and aws_secret_access_key.  Set them to your S3 access key and S3 secret access key respectively.

You are now set use s3cmd and s3sync.  Run the utilities without any arguments to get a listing of the options and commands.  I have found the -v (verbose) and –progress (progress bar) options to be great in giving me an update on what is going on during the file load/download process.  Some examples:

s3cmd.rb listbuckets  –> Lists all your buckets
s3cmd.rb createbucket/deletebucket –> Create and delete buckets
s3cmd.rb list <bucket> –> Lists all tokens in bucket
s3cmd.rb get/put <bucket>:key filename –> Copies filename from/to S3

s3sync can be used to synchronize local folders with buckets:

./s3sync.rb <bucket>:token local_dir –> sync your bucket with the local dir.  The –make-dirs option will create local directories as needed for first time downloads.

You will see that s3sync and s3cmd are very capable tools for interacting with S3.  Besides the command line, they are also scriptable and you can set up regular syncs and uploads/downloads via cron.  They have given me access to virtually unlimited cheap disk space and simplified the complexity of managing my files.

Written by M Kapoor

October 27, 2008 at 4:17 am