xyzio

Posts Tagged ‘power supply

A low cost Nixie Tube Power Supply

with 11 comments

I’ve recently become interested in Nixie tubes.  Nixie tubes are neon filled glass tubes that contain cathodes in various shapes, numbers being the most common, and a mesh anode.  Passing a current through the cathode causes the neon gas to ionize which makes it light up.

The problem with these tubes is that they voltages of around 170V in order to ionize the gas.  Fortunately, most tubes only need a few mA which makes the supply design simpler and easy to run off a wall wart.

Design:

My goal here is to create a power supply that  is cheap and works well enough to power 4 IN-17 tubes forLayout a direct drive Nixie tube clock.  My design is based on the power supply used in the ArduiNIX.

A search of the web shows that their power supply design is quite common.  I took their design and incorporated the suggestions Nick De Smith gives in his own Nixie tube design tutorial.   Nick’s supply is nice but it is expensive.  However, his suggestions are useful.  I added a solid ground plane except around the inductor and used multiple vias to connect to ground for low resistance paths.  I used large traces and expanded them to a plane wherever possible to further reduce resistance.  In addition I added capacitors to the input (C5, C6) and output (C7) to help smooth ripples.  I put the components as close together as possible and also changed the output diode to a UF4004.  Why switch the diode?  Because it was cheaper.

Cost:

So is the supply cheap?  The total component cost is $7.75.  Is it possible to make it even cheaper?  Yes.  You can directly solder your wires to the board and omit the terminal connectors (J1, J3 – $1.64).  You can also omit the input/output stabilizing capacitors (C5, C6, C7) and the IC socket for the 555 timer and save another $0.53.  This brings the total down to $5.58.

The board size is 1.8 x 1.9 inches. Assuming that you live in the US and pay $ 1.67/sq inch for your PCBs, you can build one for about $13.50 (or $11.29 with reduced components).  And, it only gets cheaper if you make more.

How Does it Work?

The supply uses a traditional switch mode topology.  The 555 timer switches inductor L1 to ground and diode D2 through transistor Q10.  L1 charges up when it is connected to ground and then acts like a current source to force charge through D2 when Q10 is off.  This charge build up on capacitor C1 provides the desired output voltage.  Potentiometer R19 and transistor Q5 form  a feedback loop that control the 555 timer’s switching frequency.

Stability:

The supply takes a while to stabilize.  In addition to switching noise, the supply output drops about 5-7 volts over the span of a few minutes after you turn it on.  It stabilizes soon afterwards.  In my tests, if I set the supply to 175v with a 100kOhm load, it stabilizes around 168v and will stay that way for several days.  Fortunately Nixie tubes are forgiving enough

HV Supply Demo

that this supply is adequate.

Construction and Usage:

Constructing the supply is simple.  Solder the indicated components into their proper places on the board.  It should take about 30 mins to assemble.  Once it is assembled, connect yourinput power supply to header J1 and a multimeter to the output header – J3.  The input supply should be around 9v.  Plug in the input power supply.  THIS INVOLVES HIGH VOLTAGES THAT CAN KILL YOU, SO DO NOT TOUCH THE HIGH VOLTAGE PORTIONS OF THE BOARD.  Look at your multimeter – it should read somewhere between 90V and 200V.  Adjust potentiometer R10 until you reach your desired voltage.  As you do this, pass your hand over the supply – you should feel no heat.  If it feels hot, or if the output voltage is low or wildly oscillating then you have a short or misplaced component.  CAUTION – Unplug the board before you check your work.

Parts list:

I’ve saved the parts list at Mouser as a project titled ‘HV Supply’:

https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=81e48496fa

Files:

The supply was designed using Eagle.  You can download the board and schematic files here:

hv_supply.zip

Update 7/4/2013: Board and schematic files without a ground plane to avoid the issue mentioned in the comments:

hv_supply_no_planes.zip

Resources:

Nick De Smith:  High Voltage Switching PSU

ArduiNIX: Arduino Powered Nixie Tube Driver

Advertisements

Written by M Kapoor

September 5, 2011 at 7:17 pm

Posted in Nixie Tube

Tagged with , , ,